D: Hemmer foot 5. E: Zipper foot 6. A: Zigzag foot 7. F: Satin stitch foot 8. C: Overedge foot 9. The presser foot will drop off. Place the selected presser foot so the pin on the foot lies just under the groove of the foot holder. Lower the presser bar to lock the foot in place. Turn off the power switch. Loosen the needle clamp screw by turning it counterclockwise. Remove the needle from the clamp. Press the large spool holder firmly against the spool of thread. Place the spool of thread on the spool pin with the thread coming off the spool as shown.
Attach the large spool holder, and press it firmly against the spool of thread. End of thread Guide the thread into the notch on the front side of the bobbin holder. Draw the thread to the left, sliding it between the tension spring blades.
Presser foot lifter Lead the thread from the spool and pass it through the thread guide. Then draw it down along the right slot. Page Needle Threader Pull the thread through the needle eye. Thread size 50 to should also work well.
Hook Guide www. Hold the needle thread lightly with your left hand. Draw up the needle thread together with a loop of bobbin thread. If you look at the top and bottom of the seam, you will notice that there are no gaps; Page Pattern Selector Dial Janome Instruction Manual Pattern Selector Dial Raise the needle and turn the pattern selector dial until the red indication is below the desired stitch. At the same time the appropriate thread tension, 0 1 2 3 4 5 6 7 8 9 zigzag width and stitch length are indicated in the upper portion of the guide message window.
This ensures even feeding at the beginning of seams and helps when sewing many layers of fabric. The wires on this foot prevent light weight fabric from rolling and creating a ridge.
Janome Excel II Decor. Do you have a question about this product? Post your question here in this forum. Report abuse Libble takes abuse of its services very seriously. Hateful or violent content For example, Anti-Semitic content, racist content, or material that could result in a violent physical act. Personal or private information For example, a credit card number, a personal identification number, or an unlisted home address. Do not modify the plug in any way. A To remove Turn to the left. To replace Turn to the right.
B B To remove Push and twist to the left. Push and twist to the right. Place the selected presser foot so the pin on the foot lies just under the groove of the foot holder.
Lower the presser bar to lock the foot in place. Red button. Remove the thumb screw by turning the screw counter-clockwise with the screwdriver. Thumb screw. Foot holder Presser bar. For as long as you keep the reverse stitch button depressed, the machine sews backwards. Reverse button.
You can raise it about 0. Presser foot lifter. Normal up position. High position. When inserting the needle into the clamp, push it up as far as it will go and tighten the clamp screw firmly. To find a good needle, put the flat side of the needle onto something flat a needle plate, glass, etc. The gap between the needle and the flat surface should be consistent.
Never use a bent or blunt needle. Needle clamp screw. Needle clamp. Always test thread and needle size on a small piece of fabric which will be used for actual sewing.
The blue tipped needle effectively prevents skipped stitches. Lift up the spool pin and place the spool of thread on it with the thread coming off the spool as shown. Press the large spool holder firmly against the spool of thread. Spool pin. Ordinary spool. Large spool holder. Small spool holder. Small spool. Gently slide the hook cover plate release button to the right and remove the cover plate.
Hook cover plate. Lift up the spool pin. Place the spool of thread on the spool pin with the thread coming off the spool as shown. Attach the large spool holder, and press it firmly against the spool of thread. Guide the thread around the thread guide.
Additional spool pin hole. Continue to draw the thread lightly until the thread slips into notch. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Do not use outdoors. Do not use bent needles. Table of Contents Names of Parts Corded Buttonhole Names of Parts 1.
Stitch length control 2. Zigzag width control 3. Foot storage compartment 4. Flip-top sewing instruction panel 5.
Top cover 6. Thread tension dial 7. Pressure dial 8. Face plate 9. Thread cutter Needle threader Hook cover plate Hook cover plate release button Extension table Accessory storage box Reverse button Needle clamp screw Presser foot Handwheel Pattern selector dial Feed balance dial Power switch Machine socket
0コメント